Maker Hacks

Ideas, news & tutorials for makers and hackers – Arduino/Raspberry Pi, 3D printing, robotics, laser cutting, and more

  • Home
  • About Maker Hacks
  • Blog
  • YouTube Channel
  • Recommendations
  • Contact
You are here: Home / Hacks, Tips, and Tutorials / Glowforge ‘Pass-Through’ Hack: Tricking the Front Flap of the Glowforge with Magnets to Increase Capacity

Glowforge ‘Pass-Through’ Hack: Tricking the Front Flap of the Glowforge with Magnets to Increase Capacity

Chris Garrett

FacebookTweetPin
glowforge-passthrough-hack

The Glowforge Basic does not have the pass-through feature of the Glowforge Pro but with this magnet hack, you can trick the front flap to think the lid is shut fully, allowing you to “pass-in” larger material than usual.

Glowforge does NOT want you to do this.

  • First, obviously, this is going to remove the safety feature that is protecting your eyes.
  • Second, you are removing the seal that makes the smoke go out of the vent rather than into your room.
Glowforge Protective Glasses

Take precautions!

Why Trick the Front Flap of Your Glowforge?

This is not a permanent hack, it just involves magnets and some tape. While this means you are not permanently changing your Glowforge, if you find you need to do this a lot, then that would probably mean you need to upgrade to a pro 🙂

The Glowforge Lid with Sensors Tricked Left and Right

Tricking the flap in this way simply allows you to fit longer pieces of material, or awkward shaped material, onto your bed.

In my case, I had acquired a large amount of off-cut plywood from a friendly guy at one of my makerspaces. I had quickly cut it on the table saw just enough to transport it, but I still needed to reduce the length for it to fit on my Glowforge.

This trick allows you to accept more generosity from materials-having friends!

Get up to $500 off your Glowforge

Save on your order with my referral link

Get Discount!

How to Trick the Glowforge Front Door

Magnets + Tape = Win
  1. Load the Glowforge UI so you can monitor in the top right of the screen where it says the lid is open. We need that to switch to “scanning” so we know we fooled it.
  2. Get a couple of cheap magnets. They don’t need to be especially strong.
  3. Move them as shown until the LED lights change – that means it thinks the lid is closing.
  4. When the screen changes from lid open to scanning, you know you have the right spots either side and can tape down.
  5. Once you are done needing the front flap open, simply un-tape the magnets and you can close it as usual.

Glowforge with Front Flap Hack (and improvised material stand/Ben)

That’s it!

Thank you to Kevin Meinert from the Facebook Glowforge group for alerting me that this was even possible!

Get up to $500 off your Glowforge

Save on your order with my referral link

Get Discount!

Related

FacebookTweetPin

by Chris Garrett Filed Under: Hacks, Tips, and Tutorials Tagged With: glowforge, hack, laser engraving, making, steemmakers

About Chris Garrett

StudioPress Marketing Director at WP Engine. Co-author of the Problogger Book with Darren Rowse. Maker of things. 🇨🇦 Canadian

☕️ Support Maker Hacks on Ko-Fi and get exclusive content and rewards!

« Creality Ender 3 3D Printer Kit Review
Raspberry Pi Security Camera »

The website for makers and hackers – Arduino, Raspberry Pi, 3D Printing and more

Get fresh makes, hacks, news, tips and tutorials directly to your inbox, plus access to the 30 Days to Arduino course

Recently Popular

  • How to choose the right 3D printer for you
  • Glowforge Review – Glowforge Laser Engraver Impressions, Plus Glowforge Versus Leading Laser Cutters
  • Original Prusa i3 Mk3S Review
  • Best 3D Printing Facebook Groups
  • Elegoo Mars Review – Review of the Elegoo Mars MSLA Resin 3D Printer
  • Glowforge ‘Pass-Through’ Hack: Tricking the Front Flap of the Glowforge with Magnets to Increase Capacity
  • How to Make a DIY “Internet of Things” Thermometer with ESP8266/Arduino
  • Wanhao Duplicator i3 Review
  • IKEA 3D Printer Enclosure Hack for Wanhao Di3
  • Creality CR-10 3d printer review – Large format, quality output, at a low price!
  • 3D Printed Tardis with Arduino Lights and Sounds
  • Anet A8 Review – Budget ($200 or less!) 3D Printer Kit Review
  • Make your own PEI 3D printer bed and get every print to stick!
  • Upgrading the Wanhao Di3 from Good to Amazing
  • How to Install and Set Up Octopi / Octoprint
  • Creality CR-10 S5 Review

Copyright © 2021 Maker Hacks